The errors in the following table might appear while you are working in UTS. Errors are listed alphabetically. Suggested responses to these errors are also provided.
Table 4-25
|
Error Message |
Suggested Response |
|---|---|
|
A 'Y' should be specified in the XMT or RCV field for transfer to occur. |
Type Y to initiate the transfer. |
|
Buffer passed to Common Dialog too small to accommodate string |
Contact Technical Support. An internal error has occurred. |
|
Cannot find Application list. Create a [UTS Host Applications] section in the Registry. See documentation for details. |
Add a UTS Host Applications key to the Windows registry. |
|
Could not write to file. |
Check the read/write attributes of the file to which you are writing. |
|
Creation of Common Dialog failed on call to DialogBox() |
Contact Technical Support. An internal error has occurred. |
|
Data in DEVMODE contradicts data in DEVNAMES |
Contact Technical Support. An internal error has occurred. |
|
Error in creating file. The filename may be invalid or this file may have a read only attribute or the disk may be full. |
Check for a valid file name, check for a read-only attribute, and/or check your disk for available space. |
|
Error in file transfer. |
Try the transfer again. |
|
Error in reading from the disk on MAPPER Upload. |
Check the disk from which you are attempting to read to ensure it is functioning properly. |
|
Error in writing to the disk on MAPPER Download. |
Check the disk to which you are attempting to write to ensure it is functioning properly and space is available. |
|
Error occurred while accessing entry in the registry. |
Check for the existence and location of the UTS Host Applications or UTS Options key in the Windows registry. |
|
Error. Currently the Terminal Index should be 1. |
Ensure a 1 is entered in this field. UTS does not support indexes other than 1. |
|
Error. Invalid Blocksize specified. |
Type a valid value for the Blocksize. It must be a decimal value. |
|
Error. Invalid Drive Letter specified. |
Select the correct drive containing the file. |
|
Error. Invalid Prompt specified. |
Type a valid value for the Prompt character. It must be a hexadecimal character. |
|
Error. Invalid Separator specified. |
Type a valid value for the Separator. It must be a hexadecimal character. |
|
Error. The Options field contains invalid characters. |
Verify the available options and enter a valid value. |
|
Error. The Specified file Does not Exist. |
Provide the proper file name. |
|
Failure allocating memory for internal Common Dialog structure |
Contact Technical Support. An internal error has occurred. |
|
Failure creating an IC |
Contact Technical Support. An internal error has occurred. |
|
Failure finding custom template for Common Dialog |
Contact Technical Support. An internal error has occurred. |
|
Failure finding specified resource |
Contact Technical Support. An internal error has occurred. |
|
Failure initializing Common Dialog. Possibly due to insufficient memory. |
Contact Technical Support. An internal error has occurred. |
|
Failure loading specified resource |
Contact Technical Support. An internal error has occurred. |
|
Failure loading specified string |
Contact Technical Support. An internal error has occurred. |
|
Failure loading the printers device driver |
Contact Technical Support. An internal error has occurred. |
|
Failure locking memory for internal Common Dialog structure |
Contact Technical Support. An internal error has occurred. |
|
Failure locking specified resource |
Contact Technical Support. An internal error has occurred. |
|
Failure parsing strings in [devices] section of WIN.INI |
Your WIN.INI file may be corrupt. Re-install your print drivers. |
|
Failure setting up resources for Common Dialog |
Contact Technical Support. An internal error has occurred. |
|
Failure subclassing during initialization of Common Dialog |
Contact Technical Support. An internal error has occurred. |
|
File I/O related errors occurred while trying to convert the data. Conversion aborted. |
Check the read/write attributes of the files that are being converted. |
|
File not opened in FILE TO PAGE transfer. |
Check for the existence of the file you are accessing, as well as its location. In addition, check the read/write attributes of the file. |
|
Filename does not contain characters. |
Select the Characters option on the Page To File dialog box to save the specified file with Characters. |
|
Filename does not contain emphasis information. |
Select the Emphasis option on the Page To File dialog box to save the specified file with Emphasis. |
|
Filename does not contain FCC information. |
Select the FCCs option on the Page To File dialog box to save the specified file with FCCs. |
|
Filename is not a binary dump file. |
Try to display the specified text file using the File To Page dialog box. The file was not originally saved using the Page to File dialog box, and the signature is not recognized. |
|
Filename was not saved from a screen having the same dimensions as the current screen. |
Change the dimensions of your current screen to the same or greater than those of the saved screen. |
|
Global Lock has failed |
Close unneeded applications to free additional memory. |
|
Instance handle not passed to Common Dialog |
Contact Technical Support. An internal error has occurred. |
|
Internal Control Page Error. |
Check your Extended Control Page options to ensure they are correct. |
|
Internal error in accessing the file. Check on disk space and/or file read/write attributes for the given file. |
Check your available memory, as well as the read/write attributes of the file you are accessing. |
|
Invalid filename or file does not exist. |
Check the file name for correct entry, or try a new file. |
|
Invalid filename passed to FileOpen or FileSave |
Contact Technical Support. An internal error has occurred. |
|
Invalid structure size passed to Common Dialog |
Contact Technical Support. An internal error has occurred. |
|
Invalid Transmit Mode |
Select a valid Transmit Mode and try again. |
|
Invalid value for Sequence Handler |
Type a valid value for the Sequence Handler and try again. |
|
MAPPER file transfer cannot be performed unless the Screen dimensions are 80 cols by 24 rows or 132 cols by 24 rows. |
Set your terminal dimensions (rows and columns) to either 24 x 80 or 24 x132 to perform MAPPER file transfers. |
|
No default printer was found |
Access the Printers section of the Windows Control Panel and assign a default printer. |
|
No default printer was found |
Access the Printers section of the Windows Control Panel and assign a default printer. |
|
No fonts exist |
Access the Fonts section of the Windows Control Panel to ensure that you have the UTS Emulation and/or UTS Emulation fonts installed. If not, re-install UTS. |
|
No hook function passed to Common Dialog but ENABLEHOOK was passed as a flag |
Contact Technical Support. An internal error has occurred. |
|
No printer device drivers were found |
Access the Printers section of the Windows Control Panel to install necessary printer drivers. |
|
Not enough memory available to create Host application list. Please close down some applications and try again. |
Close unneeded applications to free additional memory. |
|
Number Beeps is greater than Max Beeps |
Type a valid value for the number of beeps. |
|
Number of Columns is greater than Max Columns |
Type a valid value for the number of columns. |
|
Number of FCCs is greater than Max FCCs |
Type a valid value for the number of FCCs. |
|
Number of Lines is greater than Max Lines |
Type a valid value for the number of rows. |
|
Number of Pages is greater than Max Pages |
Type a valid value for the number of pages. |
|
PD_RETURNDEFAULT flag was set but either the hDevMode or hDevNames field was on zero |
Contact Technical Support. An internal error has occurred. |
|
Print Common Dialog failed during initialization |
Close open applications to free memory and try again. If error persists, contact Technical Support for additional assistance. |
|
Printer DID is greater than MAX Printer DID |
Type a valid value for the printer Device Identifier. |
|
Printer not found |
Access the Printers section of the Windows Control Panel to install necessary printer drivers. |
|
Read DID is greater than MAX Read DID |
Type a valid value for the read Device Identifier. |
|
Sufficient Memory is not available for performing TIP30 transfer, please close down applications and try again. |
Close down any applications you are not currently using to free memory. |
|
The printer driver failed to initialize a DEVMODE data structure |
Contact Technical Support. An internal error has occurred. |
|
The RID does not contain as many lines as specified in the Mapper download options dialog box. Cannot download! |
Specify a Start at Line value (for a partial transfer) that is less than or equal to the number of line in the MAPPER RID. |
|
There is not enough memory to open the profile file. Please free up some memory and try again. |
Close unneeded applications to free additional memory. |
|
There is not enough memory to process all present FCCs correctly. Close down a few screens and try again, or increase the default FCCs/Line option in configuration for this screen. |
Close unneeded applications to free additional memory. |
|
Unable to access specified record in the registry. |
Check the Windows registry to ensure that the appropriate value is listed. |
|
Unable to create a timer. Hence blinking will not be supported. All blinking characters will appear in italics. Shutdown some applications that use the timer and try again. |
Close unneeded applications to free the timer. |
|
Unable to locate keyword. |
Check the Windows registry to ensure the data for each value is correct. |
|
Unable to locate section. |
Check the Windows registry to ensure the key exists and is properly named. |
|
Unable to locate the path in the registry. Please generate a string named 'Directory' with the path to the product directory as the data under the Workstation key in the registry. See on-line help for more details. |
Run the Windows Registry Editor and add a Directory string to HKEY_CURRENT_USER\Software\Micro Focus\ Accessory Manager\Workstation. The value for this string should be the path to the executable files (such as C:\INFOCN32\ACCMGR32). |
|
Unable to open this file |
Specify a new file to open. |
|
Unable to read from this file |
Specify a new file to read. |
|
Unable to read from this file |
Specify a new file to read. |
|
Unable to retrieve report format information from the host. Mapper LZ command failed. |
Check the value of the MAPRequestLineZero option in the UTS OPTIONS key in the Windows registry. |
|
Unable to Transmit |
Check all transmission settings and try again. |
|
You are not on a valid MAPPER Report. Please open a MAPPER Report and try again. |
Ensure that you have a valid MAPPER report open in order to complete this procedure. |
|
Your destination disk does not have enough space to accommodate the data to be downloaded from the host. Do you wish to continue ? |
Choose to continue with the download, or cancel and specify a new destination or make additional space available. |